embroidery scissors to cut a piece of mohair slightly

A glue that works well is Aleenes Tacky Glue. Trim any bits that are significantly too long.Take the embroidery scissors and cut a small amount of mohair into very fine pieces. This will use three separate pieces of mohair. Mash glue into one of the pieces, and trim it off square with the regular scissors.Now, you will create the bridle path, adding realism that transforms a model horse into a real horse, well not quite real but a lot closer anyway. Trace this shape with the glue. For this, you will want to use alcohol-free mouse or spray  gel the kind with extra hold). Youll want to cut each piece one inch wide. Measure and saturate with glue as before. Once you have gained some familiarity with the process, youll be ready to work from a brand-new Breyer horse. Measure the length needed from the end of the tailbone to the ground (or to the height you want the tail to end.

Cut a little bit longer piece of mohair, still keeping it about one inch wide. Let dry for at least an hour, perhaps overnight.Trim the other two pieces at a matching angle and apply one to each side of the tailbone.Mash glue, trim, and dab on extra for the next two pieces, adding them just behind the ears so the ends hang down and blend with the first piece.Owning a Breyer model horse is fun, but whats even more rewarding is creating your own customized versions! You can achieve some stunningly realistic and beautiful results by adding a mohair mane and tail, for instance.Carefully apply the tiny, finely cut pieces to the glue and press them into the glue in a realistic way. Once the mousse has dried completely, trim any remaining excess hair and use a damp cloth or a tissue to carefully clean up any excess mousse. 

Apply a thin layer of glue across the area you want the bridle path to be  think about the shape you want it to be and how far you want it to extend.Now you are ready to create his forelock.Work glue into the cut end until saturated. Repeat the process of trimming and gluing and pushing it into the trench a little further up. Keep going until you get to the top of his neck, where his bridle path would be. Soon your friends will be asking you to teach them how to customize their model horses!. Dab glue along the edge and insert into the trench on the neck (remember, youre starting with this short piece at the withers end). Then trim straight across and hold this straight cut carefully (use the regular childrens scissors, to keep from getting glue on your embroidery scissors). You will want to start at the withers and start with shortest pieces of mane.To prepare the model horse, you will need to drill a narrow trench down the neck (with some Breyer models, you will need to trim off the hard mane which is sticking out) and trim down the hard tail to the proportionate size of a horses tailbone. Trim straight with regular scissors and apply more glue. It does not have to be a Breyer horse because these same steps will work with just about any brand of model horse.Once the glue is dry, you can carefully brush out the mane and tail (be gentle about this, so as not to dislodge your hard work).Next, you will begin gluing in his mane. Dab on a bit more glue on the end of the cut. To start with, you will need to collect some materials.Youll start gluing at the end of the tail and work your way up toward the horses body. Stick this piece onto the forehead just in front of the ears. Use toothpicks to help push the hair in. Use the embroidery scissors to cut a piece of mohair slightly longer than this.At the base of the tail, you will use three separate pieces.)Try to mash glue thoroughly into the ends of the piece of mohair. You can work on the tail while you are waiting.Allow the mane to dry for at least an hour. Wet mane and forelock with mouse and enjoy styling your new customized Breyer horse! Follow up with the tail. 

Press all the hair on securely with the fingers one last time. Stick the mohair around the end of the tailbone, so you make a layer of hair all the way around CNC Machine Tools Manufacturers not just gluing some hair to the top or the side of the tailbone). The tail should now be completely covered in hair. Dab on more glue and apply it to the top of the base of the tail. Repeat this process just a little higher up. Youll want both a pair of embroidery scissors and another small pair of scissors with pointed blades (a set designed for children is usually small enough). Trim the middle piece into a V shape with the regular scissors. Cut them longer than you will want his forelock to be, using the embroidery scissors. Small brushes that work well for styling are a toothbrush, eyebrow brush, or a gun cleaning brush. First, you will need a painted model horse (wooden or plastic) and a shank of mohair in coordinating color, at least a foot long, perhaps two feet. Keep repeating with slightly shorter pieces until you reach the base of the tail. Im sure you will want to try this again and again to craft unique collectible pieces admired by model horse lovers. You will use round toothpicks to poke the hair into place.The results are stunning! This will take some practice, so start with some used or broken models and just have some fun playing around. This is where the embroidery scissors come into play. At the end, the really fun part is the styling  you get to comb and mousse the hair into place.